CCNA3 ScaN v6.0 Chapter 10 Exam Answers 2019 2020

Last Updated on February 19, 2020 by Admin

CCNA3 v6.0 Chapter 10 Exam Answers 2019 2020 Full 100%

  1. 1. Question
    A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID?
  2. 2. Question

    Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.)

    CCNA3 v6.0 Chapter 10 Exam 009

    CCNA3 v6.0 Chapter 10 Exam 009

  3. 3. Question

    Refer to the exhibit. Which conclusion can be drawn from this OSPF multiaccess network?

    CCNA3 v6.0 Chapter 10 Exam 007

    CCNA3 v6.0 Chapter 10 Exam 007

  4. 4. Question
    Which OSPF feature allows a remote OSPF area to participate in OSPF routing when it cannot connect directly to OSPF Area 0?
  5. 5. Question

    Refer to the exhibit. What are three resulting DR and BDR elections for the given topology? (Choose three.)

    CCNA3 v6.0 Chapter 10 Exam 008

    CCNA3 v6.0 Chapter 10 Exam 008

  6. 6. Question

     
    When checking a routing table, a network technician notices the following entry:

    O*E2 0.0.0.0/0 [110/1] via 192.168.16.3, 00:20:22, Serial0/0/0

    What information can be gathered from this output?

  7. 7. Question

    Refer to the exhibit. What two conclusions can be drawn based on the output of the show ipv6 route command? (Choose two.)

    CCNA3 v6.0 Chapter 10 Exam 002

    CCNA3 v6.0 Chapter 10 Exam 002

  8. 8. Question
    Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?
  9. 9. Question
    A network engineer suspects that OSPFv3 routers are not forming neighbor adjacencies because there are interface timer mismatches. Which two commands can be issued on the interface of each OSFPv3 router to resolve all timer mismatches? (Choose two.)
  10. 10. Question
    A network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?
  11. 11. Question
    Which command can be used to view the OSPF hello and dead time intervals?
  12. 12. Question

    Refer to the exhibit. A network administrator is configuring OSPF for R1 and R2, but the adjacency cannot be established. What is the cause of the issue?

    CCNA3 v6.0 Chapter 10 Exam 005

    CCNA3 v6.0 Chapter 10 Exam 005

  13. 13. Question

    Refer to the exhibit. What the amount of time that has elapsed since the router received a hello packet?

    CCNA3 v6.0 Chapter 10 Exam 004

    CCNA3 v6.0 Chapter 10 Exam 004

  14. 14. Question
    Which two parameters must match between neighboring OSPF routers in order to form an adjacency? (Choose two.)
  15. 15. Question

    Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?

    CCNA3 v6.0 Chapter 10 Exam 006

    CCNA3 v6.0 Chapter 10 Exam 006

  16. 16. Question

    Refer to the exhibit. R1 and R2 are connected to the same LAN segment and are configured to run OSPFv3. They are not forming a neighbor adjacency. What is the cause of the problem?

    CCNA3 v6.0 Chapter 10 Exam 001

    CCNA3 v6.0 Chapter 10 Exam 001

  17. 17. Question
    A network administrator is troubleshooting an OSPFv3 configuration on an IPv6 network. The administrator issues the show ipv6 protocols command. What is the purpose for this command?
  18. 18. Question

    Refer to the exhibit. Directly connected networks configured on router R1 are not being shared with neighboring routers through OSPFv3. What is the cause of the issue?

  19. 19. Question
    An administrator is troubleshooting OSPFv3 adjacency issues. Which command would the administrator use to confirm that OSPFv3 hello and dead intervals are matching between routers?​
  20. 20. Question
    What three states are transient OPSF neighbor states that indicate a stable adjacency is not yet formed between two routers? (Choose three.)
  21. 21. Question

    Match each OSPF election criterion to its sequential order for the OSPF DR and BDR election process. (Not all options are used.)

    CCNA3 v6.0 Chapter 10 Exam 01

    CCNA3 v6.0 Chapter 10 Exam 01

  22. 22. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

    Which routers are the DR and BDR in this topology?

  23. 23. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

    A network administrator is configuring multiarea OSPFv3 on the routers. The routing design requires that the router RT1 is a DROTHER for the network in Area 0 and the DR for the network in Area 1. Check the settings and status of the routers. What can the administrator do to ensure that RT1 will meet the design requirement after all routers restart?