CCNA4 v6.0 Chapter 2 Exam Full 100%

Last Updated on February 20, 2020 by Admin

CCNA4 v6.0 Chapter 2 Exam Full 100%

  1. 1. Question
    Which three are types of LCP frames used with PPP? (Choose three.)
  2. 2. Question
    Which command can be used to view the cable type that is attached to a serial interface?
  3. 3. Question

    How does PPP interface with different network layer protocols?

  4. 4. Question
    Which address is used in the Address field of a PPP frame?
  5. 5. Question
    Which field marks the beginning and end of an HDLC frame?
  6. 6. Question
    In which situation would the use of PAP be preferable to the use of CHAP?
  7. 7. Question
    When configuring Multilink PPP, where is the IP address for the multilink bundle configured?
  8. 8. Question

    Refer to the exhibit. Based on the debug command output that is shown, which statement is true of the operation of PPP.

    CCNA4 v6.0 Chapter 2 Exam 003

    CCNA4 v6.0 Chapter 2 Exam 003

  9. 9. Question

    Refer to the exhibit. A network administrator is configuring the PPP link between the two routers. However, the PPP link cannot be established. Based on the partial output of the show running-config command, what is the cause of the problem?​

    CCNA4 v6.0 Chapter 2 Exam 002

    CCNA4 v6.0 Chapter 2 Exam 002

  10. 10. Question
    Which is an advantage of using PPP on a serial link instead of HDLC?
  11. 11. Question
    Which protocol will terminate the PPP link after the exchange of data is complete?
  12. 12. Question
    Which serial 0/0/0 interface state will be shown if no serial cable is attached to the router, but everything else has been correctly configured and turned on?
  13. 13. Question
    How much total bandwidth is provided by a T1 line?
  14. 14. Question
    A network engineer is monitoring an essential, but poor quality, PPP WAN link that periodically shuts down. An examination of the interface configurations shows that the ppp quality 90 command has been issued. What action could the engineer take to reduce the frequency with which the link shuts down?
  15. 15. Question
    A network engineer is troubleshooting the loss of MPEG video viewing quality as MPEG video files cross a PPP WAN link. What could be causing this loss of quality?
  16. 16. Question
    Which PPP option can detect links that are in a looped-back condition?
  17. 17. Question
    A network engineer has issued the show interfaces serial 0/0/0 command on a router to examine the open NCPs on a PPP link to another router. The command output displays that the encapsulation is PPP and that the LCP is open. However, the IPV6CP NCP is not shown as open. What does the engineer need to configure to open the IPV6CP NCP on the link?
  18. 18. Question
    Which three physical layer interfaces support PPP? (Choose three.)
  19. 19. Question
    What are three components of PPP? (Choose three.)
  20. 20. Question

    Refer to the exhibit. What type of Layer 2 encapsulation will be used for connection D on the basis of this configuration on a newly installed router:

    RtrA(config)# interface serial0/0/0 
    RtrA(config-if)# ip address 128.107.0.2 255.255.255.252 
    RtrA(config-if)# no shutdown

    CCNA4 v6.0 Chapter 2 Exam 001

    CCNA4 v6.0 Chapter 2 Exam 001

  21. 21. Question
    Which two statements describe a PPP connection between two Cisco routers? (Choose two.)
  22. 22. Question

    Match the PPP options with the correct description. (Not all options are used.)

    CCNA4 v6.0 Chapter 2 Exam 01

    CCNA4 v6.0 Chapter 2 Exam 01

  23. 23. Question

    Match the phases of establishing a PPP session in the correct order. (Not all options are used.)

    CCNA4 v6.0 Chapter 2 Exam 02

    CCNA4 v6.0 Chapter 2 Exam 02

  24. 24. Question

    Match the steps to the PPP CHAP authentication process sequence. (Not all options are used.)

    CCNA4 v6.0 Chapter 2 Exam 03

    CCNA4 v6.0 Chapter 2 Exam 03

  25. 25. Question

    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
    Why is the serial link between router R1 and router R2 not operational?